How to Cover Walls the Fastest

1. A Faster Way To Clean

First and foremost you need to start with a clean surface for paint to adhere to previously painted walls and woodwork. Just use a sponge and a trisodium phosphate cleaner to easily wash off dirt, and grime. Be sure to buy TSP concentrate and mix it with water, as it’s a better value than liquid TSP.

Just use TSP on all of your woodwork. It slightly etches the wood, which helps the paint form a better bond. Use it in kitchens to clean grease from walls, in bathrooms to remove hairspray and around light switches to remove fingerprints. Wear rubber gloves and turn up the cuffs to keep the TSP solution from running down your arm.Fastest_way_to_cover_your_walls

 2. Remove The “Goobers”

Even if you open your paint right after bringing it home from the paint store, you can still have small chunks or strands of hard paint in it. If those end up on the wall, you’ll have to pick them out and reroll the area. So spend two minutes straining out the ‘goobers.’

Buy a paint strainer or just use an old pantyhose to strain the paint. Place the strainer over an empty 5-gallon bucket, then pour the paint through the strainer. The strainer catches any debris in the paint. This is also a great time saver to start boxing your paint.

 3. Cut One Wall At A Time

It’s tempting to cut in along all the trim, the ceiling and the corners in the room at once, however you’ll get better results if you cut in just one wall, then immediately roll out the wall before cutting in the next one. That’s because if you roll out the wall right away, while the cut-in paint is still wet, the cut-in paint and the wall paint will blend much better, reducing the chance of lap marks.

 4. Don’t Bother Tapping Off All Your Trim

Taping off all your trim with masking tape is time consuming and doesn’t guarantee good results. Paint can still bleed under the tape. In short, taping off everything is a waste of time.

Instead, only tape horizontal surfaces, like baseboards and chair rail, where paint splatter can land and be noticeable. Vertical surfaces, like door and window trim, aren’t as vulnerable to splatter, so don’t bother taping them. Just be sure to cut in carefully with your paintbrush so you don’t slop paint onto the trim.

5. Cover That Wall Fast

If you’re right handed, paint the wall from left to right. If your left handed, paint from right to left and reverse all the following directions.

Right handed : Load the roller sleeve with paint and roll from the baseboard to the ceiling to get the paint on the wall. Then roll straight back down, without reloading the roller, to ensure the wall is covered. Load the roller and move over about 3 inchs to the right and roll the full height of the wall again to feather out the leading edge.

When you get to the top, move about 6 in. to the left, without reloading, and roll back down to smooth out any runs or lap marks. Then reload the roller, place it on the feathered edge and start the process over. As you paint, roll horizontally where you cut in along the baseboard and ceiling. Only roll about 3 ft. at a time so the paint will stay wet as you roll the walls.

Free-Quote-Article

How to Paint your Ceilings

So you’re thinking your ceiling needs a new coat of paint? The first thing you need to is decide if you are going to paint the walls also, or just the ceiling. If you are going to paint the walls, make sure you paint the ceiling first, that way you don’t have to worry about the ceiling dripping paint on finished walls.

Painting CeilingsOnce you’ve got your painting plan figured out, you need to pick out your paint. Measure the rooms height, width, and depth. Give this information to the company you decide to buy your paint from and they will assist you in determining how much paint you’re going to need to get the job done. As always, having a little extra is always a good thing in-case you need to do touch ups later.

The next step is to remove the furniture from the room, however if you live in a place where this isn’t possible move all the furniture to center the room and cover it well with a tarp or plastic.

Next, cover the floor with plastic and make sure you tape it down to prevent paint getting under the plastic onto the floor.

Now you’re prepped, but there is one more thing to sort out before you decide what you’ll be doing your painting with, and that is do you need primer? The rule is that if you intend to paint over a color that is darker than the hue you’ve selected definitely put on a primer. This will make it so the new shade won’t be bled through by the old color. It will also save you time and money to put up a primer before the finishing paint because the new color will require less coats of paint. Follow the next steps with the primer as you would with the finishing paint. Make sure you let the primer dry 24 hours before you begin painting.

Next step is to cut the ceiling, which means to paint the edges of the ceiling to minimize the amount of paint that gets on the walls.

Once the prep work is done you have a couple options:

  1. Buy or rent a paint sprayer and spray the ceiling. It’s a bit of a mess but it gets the job done, just remember if you do this, take plastic over the windows and anything you don’t want to color as a fine mist will cover everything. Easy to paint over the walls, but not as easy to get off of glass.
  2. Or use a roller to paint instead of the sprayer. If you decide to roll the ceiling you can either use a ladder to get up their comfortably or use an extension pole for your roller. Then paint the ceiling in even strokes to make sure you keep an even thickness across the area.
  3.  After you paint your ceiling, if the walls are you next step, go for it. Just make sure the ceiling is dry before you get started.If the ceiling was the only part of the room you painted, the last thing you need to do of course, is clean the room up, put the furniture back in place, and enjoy your new space.

 

Free-Quote-Article

How to Paint French Doors

French Doors

Do you have a pair of French doors that need a new look? It can be daunting task to figure out how exactly to paint those beautiful French doors with all that glass. So here we have it all broken down on exactly what you will want to do to make it as easy as possible!

Remove the Doors

Before you do anything you will want to remove the doors from their hinges. This will allow you to keep them even and steady while performing the paint job. It also will allow you easy access to all the nook and crannies of the doors. Lay out some plastic painters sheets where you will be painting, and set up two saw horses to lay the French doors across. This gives you a flat area to work.

Preparation

Once you have the doors laid out on the sawhorses. Be sure you remove any hinges, handles or metal from the doors. If there are any cracks, be sure you repair them prior to beginning painting. Use the putty to fill the cracks and holes. Let completely dry and then use sandpaper to smooth the surface. Using a damp cloth, remove any of the dust that might be left behind after sanding.

To prevent paint from getting onto the glass windows, using painter’s tape tape off the glass panes.

Prime

As with any painting project, be sure you use a primer to get the best results possible. Simply paint the door with your chosen primer and wait to dry completely. Using long strokes and going in the direction of the wood, apply the primer. While one door is drying, apply the paint to the other door. Depending on the previous color on the doors, you might need a second coat of primer. Use your best judgment.

Paint and Seal

Once the primer is completely dry, you can begin painting with your chosen color. Using the same methods (long strokes, going with the grain of the wood) apply your new coat of paint. Let dry completely, and apply a second coat. Be sure you paint both doors evenly, and if your doors face the outdoors, make sure to apply a weatherproof sealant. The sealant helps to protect your new paint from rain, sun & snow.

Finishing

After the doors are completely dry, put all the hardware back on. Remove all of the painter’s tape from the glass, and double check your work for any missed spots. Hang your doors back in their location and enjoy the look of your newly finished French doors!

Free-Quote-Article

3 Tips To Follow When Painting Your Minneapolis Home

After years of painting in the Minneapolis and surrounding areas I have picked up on lots of different things that can help homeowners when getting their homes painted. These simple tips can save you time, money and headache. So here you go!

Document All Colors, Brands and Sheens

This is so simple and is a huge time saver as well as money saver. Whether you are painting your home yourself or hiring a painting contractor. If you don’t have the paint color, brand and sheen then it is up to you (or the painter) to try to match the existing color. If you only need touch ups you may find that a matched paint doesn’t quite match as well as the original paint would have. This can cause you to have to repaint a whole wall rather than just touching up.

Use A Pole When Rolling Walls

Whenever I see those DIY shows on TV painting a wall with a roller and no handle I cringe. I have seen it too many times. With the use of an extension pole, from 1′ – 4′ or an adjustable 2′-4′ pole you will save your back, you will also find painting to be significantly easier and quicker.

You Don’t Always Have To Prime

Although every paint store will tell you to prime every single thing you paint, it is not always necessary to prime. Actually, there are only a few situations that primer is actually necessary.

  • Any raw surface such as wood, drywall, metal and so on.
  • To seal in stains on walls, wood and more.
  • To cover and bond damaged paint.

If you are repainting interior walls, you almost never need to prime your walls. Not even if they are currently a bright color.

When You Do Prime, Tint Your Primer

If you are painting a color over wood, drywall or anything that needs primer, don’t go with standard white primer. You may end up needing to add an extra coat of paint just to cover up the primer. Primers can often times be tinted up to 50% of your final color. This can easily save you a coat of paint in the end.

 

Free-Quote-Article

How To Avoid Cut In Lines When Painting

interior design of white couch on red wallHave you ever finished painting a room, all tired and ready to be done painting, stood back to admire your incredible job and then noticed that your cut in lines along the ceiling stand out like a sore thumb from the area of the walls that you rolled?

This can be seriously annoying if you are a perfectionist when you paint. This phenomenon is cause by multiple painting issues all working together against you.

Here are a few ways that you can avoid this issue and get the best looking paint job possible in your home.

Make Sure To Box Your Paint

Boxing your painting is mxing all of your paint together before starting your painting project. When you purchase a colored paint from the store there can be tiny variations in the color from one can to another. In most cases this won’t present a problem as the difference is incredibly minor, but it will help little things like cut lines show up a little more.

If your painting project requires 3 gallons of paint, use a 5 gallon bucket and pour all three gallons into the empty bucket. Stir the bucket and pour the 3 gallons back into their cans or just put a lid on the 5 gallon bucket. This will ensure that all of your paint is 100% the same color.

Overlap Your Cut Lines When Rolling

When I cut in a ceiling with a brush I typically use a 2 – 2 1/2 inch width brush and brush down about 4″-6″ from the ceiling. Then when I go back over the brushed in area while rolling the wall, I try to get as close to the ceiling as possible without actually touching the ceiling. This usually means only about 2 inches of my brush strokes don’t get covered while rolling.

Roll Out Your Walls Soon After Cutting In Ceilings

Not allowing the paint to 100% dry in-between will help your cut-in lines and your rolling texture to blend better.

Avoid Cheap Paint

Three is truth in “You get what you pay for” and this can absolutely true with paint. If you’re buying $10-$15 a gallon paint, expect issues such as cut in lines standing out and poor coverage. I recommend going with a $20+ gallon of paint usually (my favorite being Behr from Home Depot, it’s priced well, performs great, and has a great warranty).

 

Free-Quote-Article

Wall Painting Do’s and Don’ts

Part 1

There are a handful of reasons you may be thinking about painting your walls. These may range from selling your home, brightening up a room or maybe you even just bought a new home. Whether you plan on painting yourself or hiring a contractor, you want your home to look amazing when you are done. This article is meant for the Do It Yourself home owners out there who want great results with their painting project. Just a note, if you are thinking about hiring a contractor, Minneapolis Painting Company will make sure you receive an amazing paint job for an amazing price!

Don’t Use Fall For Gimmicks Such Edging Tools

Everyone want’s to be able to paint easier and faster and many of these tools promise just that. Problem is, they don’t deliver. I can promise you that almost all of these edging tools and cut in tools are a waste of time and money. They will give you an ok edge at best and are a paint to clean, so you will probably only get one use out of them.

Do Buy A Nice Paint Brush

PurdyInstead of using a gimmicky edging tool, use what a real professional painter would use, a high quality Purdy or Wooster paint brush. These brushes are made to last. If you take your time, you can cut in a near perfect line on trim or ceilings with these. They are also so much more useful, one high quality brush will server the same purpose as 4 different painting gimmicks. If kept clean a Wooster or Purdy brush should last you 10+ years. I have Purdy’s that I have been using almost daily for over 5 years.

Don’t Skimp On Your Brush, I just told you to buy a nice brush, I did not say to buy a cheap brush. Cheap brushes will loose their shape, not clean well, deliver poor results and need replacing soon. A good quality brush is always going to be $10-$18, anything less is cheap.

 

Don’t Skimp On Your Roller Pads Either

A cheap roller pad will shed lint all over in your paint. This will cause your wall to look terrible. A cheap pad will also make your painting take longer, leave a poor texture. A high quality roller will not shed in your paint, hold more paint between dipping, leave a great texture and help you paint faster. A good roller cover would be a Purdy White Dove Roller Cover. Look for a 1/2″ nap for best results.

Do Use An Extension Pole When Rolling Paint On Your Walls

I like to use a 2′-4′ extension pole when painting walls for a couple of reasons. First, an extension pole saves my body. When I paint with an extension pole my back stays in a upright position with my arms doing all of the work. Without an extention pole you must bend down and reach up on every stroke. This will take a toll on your body. Secondly, for the exact reasons I mentioned, an extension pole will help you to paint significantly faster.

Extension Pole

Free-Quote-Article

How To Get Mold Out!

cute green monsterHomes that develop mold often have an underlying issue that contributes to the mold. A home that is dry will not develop mold. Therefore, if you notice that your home has a mold problem, you likely also have a moisture problem that is causing the mold to grow. Once you discover the mold in your home, you must evaluate its extent and determine if the problem is small enough to handle on your own or if you need a professional mold removal company to complete mold remediation.

How To Get Mold Out / How To Treat Mold

The first step in the mold removal process is to determine the cause of the mold. In some cases, you may have a water leak somewhere in your home that is feeding the mold. In others, the mold may be caused by a damp basement. Discovering the source of the water that causes the mold to grow is important. If you remedy the mold problem without fixing its source, the mold will keep recurring, costing you more money to fix in the end. Therefore, you must find the source and fix that problem first.

After you have corrected the moisture problem that contributed to your mold problem, you need to evaluate the extent of the mold damage. The types of damage you find will have an impact on the mold removal techniques you use through the remediation process. The types of materials damaged by the mold will also impact your cleaning techniques. Depending on the extent of damage and the materials involved, you may need to use more than one method during your clean-up process.

Cleaning up a mold problem requires more than just washing the area with bleach. Even though bleach kills mold, it isn’t approved by the environmental protection agency for the purpose of cleaning mold problems. If liquid is present along with the mold, use a wet-dry vacuum to remove the liquid and mold from the area. However, if the area is simply damp, do not use a wet-dry vac or you will spread the spores instead. On hard, dry surfaces, wipe the area with wipes or a cloth dipped in a water and detergent mixture. Dry the area thoroughly after mold removal to prevent recurrence. If you must vacuum a dry area, use a vacuum with a HEPA filter to ensure proper mold removal. If you don’t use a HEPA filter, the vacuum will spread the spores around instead of removing them.

While you should be able to succeed in mold removal from most materials, some items can’t be salvaged when mold is involved. Items made from paper typically must be thrown out if they are impacted by the mold. Any material that is porous should be discarded. However, you shouldn’t simply throw these items in your trash cans. The infected materials must be sealed completely in two polyethylene plastic bags before you throw them away. If items are too large for plastic bags, wrap the items in polyethylene sheets and use duct tape to seal the wrapping.
Signs of a Mold Problem

  • If you notice a water leak or moisture problem in an area of your home, chances of finding a corresponding mold problem is high. A pipe break, sewer backup or even steam from your shower can result in a mold problem.
  • A musty smell in your home can be an indicator of the existence of a mold problem in your home, especially if you didn’t notice the smell before.
  • Many people are allergic to molds. If you or someone else in your home suddenly experiences allergy-type symptoms, particularly respiratory problems, that aren’t related to a cold or other illness, you may be dealing with a mold problem.
  • Some people also experience other health-related problems when exposed to mold. Other sudden symptoms to watch for in your family include memory loss, skin irritation and fatigue. The sudden onset of any of these symptoms can be an indicator of mold.
  • Changes to your home that are commonly associated with moisture problems can help you identify a mold problem. Some changes to watch for include yellowing of the walls, black spots or warped wood.
  • Visible mold is often one of the last signs that you have a mold problem. The mold problem often starts long before you can actually see the mold. If you can see mold, you have a much bigger problem and will likely need professional help to clean it up properly.
Free-Quote-Article

Covering Up Ugly Brick Walls

Brick can be an attractive building material, but over time that brick wall can fade, chip and crack, leaving behind an exposed brick wall that ruins the good looks of a room. If your home has one or more of these exposed brick walls, you have a number of options for covering it up and giving that space a whole new life.

The Cover and Paint Approach

Modern-Living-Room

You can always cover the entire brick wall to hide it from view and make it a more integral part of the room. Cut a piece of drywall to the same size as the exposed brick wall you want to cover. Attach it to the brick wall using a fast-fixing glue. Press the drywall sheet into place and wait for the glue to dry.

Paint the drywall as you would with any other interior wall in a color that matches the rest of your interior design. You can jazz the wall up further with painted designs, including stencils.

Create a Textured Look

Cover the exposed brick wall with cement render if you want to maintain the texture of the wall. Cement render is also known as stucco, and it is generally made up of sand, cement and lime plaster. You can choose from textured, troweled or polished cement render or stucco. Apply the render according to the instructions on the package.

If stucco is not your style, you may prefer the look of a fine veneer or textured stone. Apply a veneer to the exposed brick wall to cover it up and make it look better. You can find veneers made of a number of designed, including sandstone, tile, stones and small pebbles.

The veneer can be applied to the brick using a special adhesive available from the same hardware stores and home improvement centers that sell the veneer itself. Choose a design and a veneer that matches the style and decor of your home.

Cover Up the Wall

If you prefer, you can simply disguise and cover up that unsightly brick wall. Cover the exposed brick wall with fabric panels or with a single large curtain. You can also use adhesive to hang pictures and artwork directly on the exposed brick wall if you like.

Transform That Brick Wall into a Work of Art

White-Room-With-Brick-Accent

You do not have to live with that unsightly brick wall, and with the right approach you may not even need to cover it up. If you paint the individual bricks, you can transform the look of the entire wall and give it an entirely new appearance.

Paint individual bricks in the wall to create a pattern. Change the paint to create a new look whenever you want. While this does not strictly cover up the exposed brick wall, painting the bricks can make them more attractive.

Create a Wall Photo Gallery

Place a room divider in front of the exposed brick wall to hide it. You can choose a room divider consisting of a number of photo frames, and use that to transform your ugly brick wall into a picture gallery. Measure the brick wall, then purchase enough room dividers to cover the entire wall. You can disguise the top of the brick wall with sheer curtains or decorative panels.

These tips can help you make the most of your exposed brick wall, either by covering it up, disguising it or transforming it. With the right tools and the right techniques, you can transform that ugly old wall into a place of uncompromising beauty and style.

Free-Quote-Article

How to Avoid Spray Paint Drip Marks

If you are planning to spray paint something in your home, you might be worried about those dreaded drip marks that every person seems to get. While these may seem unavoidable at times, they are the result of poor painting techniques. Why do you think professional painters are able to spray paint cabinet doors and large walls without any drips at all? It is because they have the tools and expertise to do the job the right way. In order to get the same results they do, follow the tips below.

2012-11-16_09-29-34_140

Spray in Light Layers
The key to having a nice, smooth finish with spray paint is to use light layers. Rather than trying to coat everything in one shot, allow one layer to dry completely before applying another. This may take more time, but it will allow you to get a nice, even layer of paint that won’t drip. By rushing through the paint job, you build up more paint on the surface than what can easily dry. The result is a lovely line of drippage every time.

Spray Parallel to the Ground
Don’t point the nozzle of the spray can down. That will reduce the amount of paint that can come through the distribution hose. Instead of doing that, you need to spray parallel to the ground so that the hose can suck up as much paint as possible. This follows the same theory of trying to using a pen to write on the ceiling. It won’t work long because the ink can’t get to the tip of the pen. Keep that in mind as you start using spray paint.

Refill Often
You may notice your spray paint looking worse as you run out of paint. That is because there is less paint coming through the nozzle to create the pressure needed for proper spraying. If you are using a standard spray can, get a new one when it ¾ empty. If you are using a spray gun, make sure there is a decent amount of paint available at all times. This will ensure smooth results every time.

If you cannot get your spray paint to look right, call on some professional painters to get the job done for you. They can be out in no time to make your project look the way it should.

Free-Quote-Article

Painting Countertops: How To Refinish Laminate

Laminate countertops are designed for their durability and affordability. They will last for years with little care, and don’t need polishing or resurfacing like other materials. They also look the same for their entire lifespan. This may not be appealing as you change your home’s décor with the current fashions. Many people believe that you can’t paint your laminate countertops because the paint won’t stick. This is only partly true. Most paint will not stick to laminate for any length of time. However, if you use the right paint and prepare the surface properly, painting countertops can be done and can last for years.

CountertopsPainting Countertops: Step 1

Start by hand sanding the laminate’s surface with 80-grit sandpaper. Work at the surface until all the shine is gone and it looks rough. Be careful not to sand any one area too deeply or the counter will be uneven.

Painting Countertops: Step 2

Next, wash the counter with trisodium phosphate (TSP) to remove any further dust or residue. Rinse it with plain water and dry carefully before proceeding.

Painting Countertops: Step 3

Stir an adhesion primer with a stir stick and pour it into a paint tray. Spread the primer evenly over the counter you are painting with a sponge roller that has a thin nap. The ideal primer will be an adhesion epoxy primer, but if you can’t find one use an adhesion primer designed for slick surfaces like laminate. You can have the primer tinted to match your paint for a richer color.

Painting Countertops: Step 4

After the primer has cured according to the package instructions, apply a coat of epoxy paint over it. Use a sponge roller like you did with the primer. Allow it to cure, and then apply a second coat. After you have finished applying the second coat, run the sponge roller across the surface from left to right so all the paint is lying in the same direction. This gives the paint an even look. If you want, you can use a painting technique, such as sponging or stencilling, to give the counter some texture. This requires using more than one color.

Painting Countertops: Step 5

When the second coat has cured, rub a polyurethane topcoat over the counter using a rag. The topcoat will go on cloudy and dry clear. It dries in less than five minutes. After it has dried, repeat the application until you have four or five coats of polyurethane on the counter. Leave it to cure for at least 12 hours before using the surface.

What Products Can I Use for Professional Countertop Painting Results?

If you want to do some countertop painting that will fool your visitors into thinking that you have Granite Countertops, there are currently a handful of great products on the market that will give you these results. Currently two major brands that offer products to help you achieve amazing looking painted countertops. They are Rust-oleum and Giani. While they both have their pros and cons, Giani is the cheaper of the two options and Rust-Oleum is more recognized and trusted brand.

Despite using quality products when painting countertops, the counter is still vulnerable to wear and tear. When cleaning it, use only non-abrasive cleaners and a soft cloth. Avoid spilling any food that will stain the paint and wipe up spills quickly. By keeping the counter as clean as possible, you won’t have to scrub it and the paint will last a lot longer.

Free-Quote-Article